DT125R ARCHIVE

Members Login
Username 
 
Password 
    Remember Me  
DT125R Forum -> Tuning -> re linering
Post Info TOPIC: re linering
john01


DTR Respected Member

Status: Offline
Posts: 50
Date:
re linering
Permalink  
 

hi just for a start can someone please actually help me insted of just ignoring my postes. anyway is it possible to have the barrel re linered. and how much will it cost. is it just more economical to buy a new barrel. please actually help me this time it would be much apriciated thankes jon-01furiousfuriousfuriousfuriousfuriousfuriousevileyefuriousfurious

Attachments
__________________
91civic_VT


DTR Respected Member

Status: Offline
Posts: 33
Date:
Permalink  
 

Are you having fun under there? lol!

Sorry I can't really answer your question, but you could probably get a decent used barrel of ebay for not much.

What has happened to your barrel?

If its not too scored you could get it overbored slightly and fit an oversize piston and rings.

__________________
john01


DTR Respected Member

Status: Offline
Posts: 50
Date:
Permalink  
 

hi the barrel is not to scores but i am not sure if it has any barrel left to be rebored!! also when re fitting the powervalve i cant figure out which way it should facecrycan u help. lol



__________________
91civic_VT


DTR Respected Member

Status: Offline
Posts: 33
Date:
Permalink  
 

Been having my own problems with the power valve lol!

If you dont have a servo and just want to pin it so it is open, then make sure the hollow is inline with the top of the port.

It should be roughly in this position (only half the valve is in that pic)



-- Edited by 91civic_VT at 22:13, 2007-06-04

__________________
r0bsk1


DTR Senior Member

Status: Offline
Posts: 183
Date:
Permalink  
 

replating info seeing as you asked so nicely....nothmm

http://www.stanstephens.com/nicosil.htm

__________________
john01


DTR Respected Member

Status: Offline
Posts: 50
Date:
Permalink  
 

sorry about being rude but my questions usually get ignored on this forum , but thanks for the info. jon01

__________________
john01


DTR Respected Member

Status: Offline
Posts: 50
Date:
Permalink  
 

also with the power valve what positon do i put it in when fitting a servo/pully? thenks jon01

__________________
91civic_VT


DTR Respected Member

Status: Offline
Posts: 33
Date:
Permalink  
 

I think it should be set up so that it starts from the fully open position.

Just make sure the mark in the plastic lines up with the hole behind it and that the valve is open when in this position and not going to hit the piston.

__________________
john01


DTR Respected Member

Status: Offline
Posts: 50
Date:
Permalink  
 

thanks!! ( is it possible for the piston to actually hit the powervalve?!!!) beter get it right!!smile.gif

__________________
91civic_VT


DTR Respected Member

Status: Offline
Posts: 33
Date:
Permalink  
 

Yeah if the round part is at the back it will hit the piston, so it you were to turn it anti-clockwise on that pic it would hit.

__________________
john01


DTR Respected Member

Status: Offline
Posts: 50
Date:
Permalink  
 

thanks you are a legand you just saved me totally screwing my barrel!!!!! took it out to dicover thati had put it in backwares. chears.could have been closesmile.giflol!idea

-- Edited by john01 at 19:07, 2007-06-05

__________________
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
DT125R Forum -> Tuning -> re linering
Tweet this page Post to Digg Post to Del.icio.us


Create your own FREE Forum
Report Abuse 		Powered by ActiveBoard