DT125R ARCHIVE

Members Login
Username 
 
Password 
    Remember Me  
DT125R Forum -> PLASTICS -> Rear Fender HPIRES
Post Info TOPIC: Rear Fender HPIRES
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
RE: Rear Fender HPIRES
Permalink  
 

seat cover, rear fender and tail tidy came today so only took 5 days!! definately going to use him again and id reccomened to everyone to go through his site rather than ebay as its cheaper and i didnt have any problems at all, also i didnt realise how small the tail tidys were now i no why everyone likes them lol wil have to take before and after pics for you all

this is his site if ur using google chrome it translates it to english for u and u can still use paypal to buy ur stuff there check it out guys

http://www.motofiled.com/

__________________
Dt125R 02 plate
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

Nice mate, good to know they deliver quickly off their main site aswell as ebay. I need a new seat cover and two new rad scoop decals!! Mite get a hpires rear fender aswell if i like the one on yours!!

Make sure you get pics up!!!!!

__________________
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

yeah will definately get pics up and its worth saving a couple of quid by just buying straight of his site and with using ebay ur still insured i beleive, might have ago at fitting it 2moro will take plenty of pics for you all

__________________
Dt125R 02 plate
MisterDave


DTR Respected Member

Status: Offline
Posts: 69
Date:
Permalink  
 

Did you buy the bolts off ebay? I am going to need a load of bolts for my DTR as it came with a serious amount missing. I got piad today so the project seriously gets the go ahead get bike back from garage thursday and going to motofiled a whole plastic set :D
did anyone add his website to the "sticky" thread?

__________________
Bikes: Yamaha XT125X [2007] {sold} Yamaha DT125R [1997]
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

no i havnt got the bolts yet, done the seat cover today and it was a bitch to fit stretching it round that curve was really hard, also the tail tidy looks like its going to be hard going to a mates tomorrow aso he can weld a couple of bars across the back to bolt it onto then it should look ok

__________________
Dt125R 02 plate
craigbulmer


Guru

Status: Offline
Posts: 1160
Date:
Permalink  
 

conn you wont need to weld bars on mate, just screw it into your rear fender, if you use stainless bolts that dont rust it will look fine.

__________________
Yamaha DT125R - 2003
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

My tail tidy screws thru the rear fender aswell dont think you will need bars welding in tbh.

My rear fender decal is stuck on over top of the bolts so you cant see them anyway.

__________________
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

i was thinking of doing that tbh with you but didnt want to ruin the look is the rear fender going to be strong enough to hold the weight of the tail tidy, numberplate and L plate

-- Edited by conn1987 on Sunday 18th of April 2010 06:37:37 PM

__________________
Dt125R 02 plate
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

could you show me pics pls

__________________
Dt125R 02 plate
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

Tbh my tail tidy does wobble about abit as there isnt much support!! Thats what has caused the stress marks on my rear fender.

I cant tell when im riding but my mates have said it wobbles about when they are following me.

It will defo hold the weight of it all but i would say it might wobble a bit. On my bike tho the small frame thing that holds the original number plate bracket on and i think are grab rails for pillions has been removed. Are you leaving that on there?


-- Edited by fray on Sunday 18th of April 2010 06:45:59 PM

__________________
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

lol well il see if my mate can weld it for me if not then il just bolt it through

-- Edited by conn1987 on Sunday 18th of April 2010 06:43:58 PM

__________________
Dt125R 02 plate
craigbulmer


Guru

Status: Offline
Posts: 1160
Date:
Permalink  
 

does yours still have the grab rail? i tucked mine between the grab rail and rear fender. Is well supported and doesnt rattle.

__________________
Yamaha DT125R - 2003
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

craigbulmer wrote:

does yours still have the grab rail? i tucked mine between the grab rail and rear fender. Is well supported and doesnt rattle.



not any more!! the new rear fender i got wont fit with it on also the screws holding the rack on was rounded off so had to get the dremel out and just cut it off lol



__________________
Dt125R 02 plate
craigbulmer


Guru

Status: Offline
Posts: 1160
Date:
Permalink  
 

haha fair1 then!!!

__________________
Yamaha DT125R - 2003
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

Any piccies yet conn? Not sure on weather to get one ov those rear fenders yet?

I dont want to be able to see the end of the subframe sticking out from underneath the fender if you get me!!!

__________________
woll


Guru

Status: Offline
Posts: 407
Date:
Permalink  
 

fray i've got one of them rear fenders if you take the rear grab rail off you can't see anything, and i also drilled my rear fender to put tailtidy on

__________________
Mark
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

cheerz woll, yeh my grab rail is removed. think im gonna go ahead and order one then!

__________________
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

will get pics up 2moro as iv still got to sort out my L plate, i left the grab rail on the exhaust side as i use this to pick/drag the back end round to get it into my shed lol, also the tail tidy light is really small just waiting to get pulled for it now lol

Edit: also i attached it to the rear fender in the end and then used some cable ties to attach it to the frame and its solid doesnt flap at all


-- Edited by conn1987 on Sunday 25th of April 2010 07:01:24 PM

__________________
Dt125R 02 plate
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

Good idea with the cable ties!! Will be good to see some pics. Ive just ordered me a new tail tidy and wanna fit it so it doesnt wobble!

Just wondering what ppl have done for graphics for their hpires rear fenders? I wanna order one but dont want to leave it plain without graphics.

Have had a look on d&d's website but they only come in full sets and i only want the rear fender decal!!!

__________________
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

im going to stick the L plate on mine and with the cable ties on it its solid will get some pics up n the weekend, what tail tidy did u get in the end?

__________________
Dt125R 02 plate
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

Ive gone for this tail tidy. Its an acerbis one. The one im removing is faulty!

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=220592760981&ssPageName=STRK:MEWNX:IT


Have ordered a hpires rear fender 2nite aswell smile.gif

__________________
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

Just to let folk know the bloke who sells the hpires rear fender does stock graphics to fit it. It he hasnt got any listed email him and he will sort it.

__________________
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

do u have a pic mate?

__________________
Dt125R 02 plate
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

Here ya go mate, hes listed some on ebay now.

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=200466221514#ht_964wt_1167

__________________
conn1987


DTR Senior Member

Status: Offline
Posts: 125
Date:
Permalink  
 

yeah they look ok might get some my self

__________________
Dt125R 02 plate
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

Yeh will stop it from looking plain. Theres a matching one for the front too!! lol smile.gif

__________________
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

Got my rear fender today. Fitted it along with my new acerbis tail tidy. Was easy to fit, had to drill 3 holes in the top for the tail tidy and 2 each side for the fixings to the frame.

Anyone interested in seeing the pics

http://www.activeboard.com/forum.spark?aBID=66365&p=3&topicID=34459996&page=3#lastPostAnchor

__________________
Seiki


Admin

Status: Offline
Posts: 2156
Date:
Permalink  
 

no lol

__________________
fray


Guru

Status: Offline
Posts: 481
Date:
Permalink  
 

haha cheeky fooka!!

its the yz stickers ay it!!!!

__________________
craigbulmer


Guru

Status: Offline
Posts: 1160
Date:
Permalink  
 

yes!!! you finally getting it!!!



hahah

__________________
Yamaha DT125R - 2003
«First  <  1 2 3  >  Last»  | Page of 3  sorted by
 
Quick Reply

Please log in to post quick replies.
DT125R Forum -> PLASTICS -> Rear Fender HPIRES
Tweet this page Post to Digg Post to Del.icio.us


Create your own FREE Forum
Report Abuse 		Powered by ActiveBoard